|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
www.fairchildsemi.com KA2S0965/KA2S09655 Fairchild Power Switch(SPS) Features * * * * * * * * * Wide operatimg frequency range up to (150kHz) Pulse by pulse over current limiting Over load protection Over voltage protecton (Min. 23V) Internal thermal shutdown function Under voltage lockout Internal high voltage sense FET External sync terminal Latch up Mode Description The SPS product family is specially designed for an offline SMPS with minimal external components. The SPS consist of high voltage power SenseFET and current mode PWM Controller IC. control IC features a trimmed oscillator, under voltage lock-out, leading edge blanking, optimized gate turnon/turn-off driver, thermal shut down protection, over voltage protection, temperature compensated precision current sources for loop compensation and fault protection circuit. Compared to discrete MOSFET and controller or RCC switching converter solution, a SPS can reduce total component count, design size, weight and at the same time increase &efficiency, productivity, and system reliability. It has a basic platform well suited for cost-effective Monitor power supply. TO-3P-5L 1 1. DRAIN 2. GND 3. Vcc 4. FB 5. Sync Internal Block Diagram #3 VCC 32V 5V Vref - 5V + 6.4V #4 FB 2A 1mA 2.5R 1R 9V + 7.5V - + 25V - Thermal S/D OVER VOLTAGE S/D - + 0.1V S R Q #2 GND OSC S R L.E.B Q Good logic Internal bias #1 DRAIN SFET #5 Sync Power on reset Rev. .5.0 (c)2000 Fairchild Semiconductor International KA2S0965/KA2S09655 Absolute Maximum Ratings Characteristic Drain-source (GND) voltage (1) Symbol VDSS VDGR VGS IDM (3) Value 650 650 30 36.0 950 9.0 5.8 30 -0.3 to VSD 170 1.33 -25 to +85 -55 to +150 Unit V V V ADC mJ ADC ADC V V W W/C C C Drain-Gate voltage (RGS=1M) Gate-source (GND) voltage Drain current pulsed (2) Single pulsed avalanche energy EAS ID ID VCC VFB PD Continuous drain current (TC=25C) Continuous drain current (TC=100C) Supply voltage Analog input voltage range Total power dissipation Operating temperature Storage temperature Derating TOPR TSTG Notes: 1.Tj=25C to 150C 2.Repetitive rating: Pulse width limited by maximum junction temperature 3.L=20mH, VDD=50V, RG=27, starting Tj=25 C 2 KA2S0965/KA2S09655 Electrical Characteristics (SFET part) (Ta = 25C unless otherwise specified) Characteristic Drain-source breakdown voltage Symbol BVDSS Test condition VGS=0V, ID=50A VDS=Max., Rating, VGS=0V VDS=0.8Max., Rating, VGS=0V, TC=125C VGS=10V, ID=4.5A VDS=50V, ID=4.5A VGS=0V, VDS=25V, f=1MHz VDD=0.5BVDSS, ID=9.0A (MOSFET switching time are essentially independent of operating temperature) VGS=10V, ID=9.0A, VDS=0.5BVDSS (MOSFET switching time are essentially independent of operating temperature) Min. 650 - - - 5.0 - - - - - - - - - - Typ. - - - 0.96 - 1750 190 78 20 23 85 30 74 12 35.4 Max. - 50 200 1.2 - - - - 50 55 180 70 95 - - nC nS pF Unit V A A S Zero gate voltage drain current IDSS Static drain-source on resistance (note) Forward transconductance Input capacitance Output capacitance Reverse transfer capacitance Turn on delay time Rise time Turn off delay time Fall time Total gate charge (gate-source+gate-drain) Gate-source charge Gate-drain (Miller) charge (note) RDS(ON) gfs Ciss Coss Crss td(on) tr td(off) tf Qg Qgs Qgd Note: Pulse test: Pulse width < 300S, duty cycle < 2% 1 S = --R 3 KA2S0965/KA2S09655 Electrical Charcteristics (CONTROL part) (Ta = 25C unless otherwise specified) Characteristic REFERENCE SECTION Output voltage (1) Temperature Stability (1)(2) Symbol Vref Vref/T Test condition Min. Typ. Max. Unit Ta=25C -25CTa+85C 4.80 - 5.00 0.3 5.20 0.6 V mV/C OSCILLATOR SECTION Initial accuracy Frequency change with temperature (2) Sync threshold voltage PWM SECTION Maximum duty cycle FEEDBACK SECTION Feedback source current Shutdown delay current IFB Idelay Ta=25C, Vfb=GND Ta=25C, 5VVfbVSD 0.8 1.4 1 1.8 1.2 2.2 mA A Dmax - 92 95 98 % (3) FOSC F/T VSYTH Ta=25C -25CTa+85C Vfb=5V 18 - 6.0 20 5 6.4 22 10 6.8 kHz % V OVER CURRENT PROTECTION SECTION Over current protection UVLO SECTION Start threshold voltage Minimum operating voltage TOTAL STANDBY CURRENT SECTION Start current Operating supply current (control part only) VCC zener voltage SHUTDOWN SECTION Shutdown Feedback voltage Thermal shutdown temperature (Tj) SOFT START SECTION Soft start current Soft start voltage ISS VSS Sync & S/S=GND VFB=2V 0.8 4.7 - 5.0 - 5.3 mA V (1) IL(max) KA2S0965 KA2S09655 5.28 4.40 6.00 5.00 6.72 5.60 A Vth(H) Vth(L) - After turn on 14 9 15 10 16 11 V V IST IOPR VZ VCC=14V Ta=25C ICC=20mA - - 0.1 6 30 0.3 12 32.5 0.55 18 35 mA mA V VSD TSD 6.9 140 7.5 160 8.1 - V C NOTE: 1. These parameters, although guaranteed, are not 100% tested in production 2. These parameters, although guaranteed, are tested in EDS(water test) process 3.The amplitude of the sync. pulse is recommended to be between 2V and 3V for stable sync. function. 4 KA2S0965/KA2S09655 Typical Performance Characteristics (These characteristic graphs are normalized at Ta = 25C) Fig.1 Operating Frequency 1.2 1.15 1.1 1.05 Fosc 1 0.95 0.9 0.85 0.8 -25 0 25 50 75 100 125 150 1.2 1.15 1.1 1.05 Ifb IFB 1 0.95 0.9 0.85 0.8 -25 Fig.2 Feedback Source Current 0 25 50 75 100 125 150 Temperature [C] Temperature [C] Figure 1. Operating Frequency Figure 2. Feedback Source Current Fig.3 Operating Current 1.2 1.15 1.1 1.05 lIop 1 OPR 0.95 0.9 0.85 0.8 -25 1.1 1.05 IL(MAX) 1 Ipeak Fig.4 Max Inductor Current 0.95 0.9 0.85 0 25 50 75 100 125 150 0.8 -25 0 25 50 75 100 125 150 Temperature [C] Temperature [C] Figure 3. Operating Current Figure 4. Max. Inductor Current 1.5 1.3 Fig.5 Start up Current 1.15 1.1 1.05 Fig.6 Start Threshold Voltage IST Istart 1.1 0.9 0.7 0.5 -25 Vth(H) 1 Vstart 0.95 0.9 0 25 50 75 100 125 150 0.85 -25 0 25 50 75 100 125 150 Temperature [C] Temperature [C] Figure 5. Start up Current Figure 6. Start Threshold Voltage 5 KA2S0965/KA2S09655 Typical Performance Characteristics (Continued) (These characteristic graphs are normalized at Ta = 25C) Fig.7 Stop Threshold Voltage 1.15 1.1 1.05 1.15 1.1 1.05 Fig.8 Maximum Duty Cycle Vth(L) Vstop 1 0.95 0.9 0.85 -25 0 25 50 75 100 125 150 Dmax 1 0.95 0.9 0.85 -25 0 25 50 75 100 125 150 Temperature [C] Temperature [C] Figure 7. Stop Threshold Voltage Figure 8. Maximum Duty Cycle Fig.9 Vcc Zener Voltage 1.2 1.15 1.1 1.05 Vz 1 0.95 0.9 0.85 0.8 -25 1.15 1.1 1.05 Fig.10 Shutdown Feedback Voltage Vsd 1 0.95 0.9 0 25 50 75 100 125 150 0.85 -25 0 25 50 75 100 125 150 Temperature [C] Temperature [C] Figure 9. VCC Zener Voltage Figure 10. Shutdown Feedback Voltage Fig.11 Shutdown Delay Current 1.2 1.15 1.1 1.05 Idelay 1 0.95 0.9 0.85 0.8 -25 1.15 1.1 1.05 Fig.12 Over Voltage Protection Vovp 1 0.95 0.9 0 25 50 75 100 125 150 0.85 -25 0 25 50 75 100 125 150 Temperature [C] Temperature [C] Figure 11. Shutdown Delay Current Figure 12. Over Voltage Protection 6 KA2S0965/KA2S09655 Typical Performance Characteristics (Continued) (These characteristic graphs are normalized at Ta = 25C) Fig.13 Soft Start Voltage 1.15 1.1 1.05 2.5 2 1.5 Fig.14 Drain Source Turn-on Resistance Vss 1 0.9 0.95 0.85 -25 Rdson 1 0.5 0 25 50 75 100 125 150 0 -25 0 25 50 75 100 125 150 Figure13. Soft Start Voltage Figure 14. Drain Source Turn-on Resistance 7 KA2S0965/KA2S09655 Package Dimensions TO-3P-5L 8 KA2S0965/KA2S09655 Package Dimensions (Continued) TO-3P-5L (Forming) 9 KA2S0965/KA2S09655 Ordering Information Product Number KA2S0965-TU KA2S0965-YDTU KA2S09655-TU KA2S09655-YDTU TU : Non Forming Type YDTU : Forming Type Package TO-3P-5L TO-3P-5L(Forming) TO-3P-5L TO-3P-5L(Forming) Rating 650V, 9A 650V, 9A Over current protection 6A 5A 10 KA2S0965/KA2S09655 11 KA2S0965/KA2S09655 DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR INTERNATIONAL. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. www.fairchildsemi.com 9/7/00 0.0m 001 Stock#DSxxxxxxxx 2000 Fairchild Semiconductor International 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. |
Price & Availability of KA2S09655- |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |